Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Spring Replacement Cost in Edison?
Spring replacement in Edison typically costs $180 – $340 for one torsion spring, and that range covers both the part and the labor. If you have a matched pair and both springs are being replaced together (which is common once one fails), expect about twice that, roughly $360 – $680 total. The written estimate we provide after looking at your door sets the final price, and getting that estimate costs nothing.
Most spring failures are not subtle. A loud bang from the garage, a door that opens a few inches and stops, or a door that suddenly feels impossibly heavy are the usual signs. When that happens, the door is unsafe to use until a trained technician takes a look. Call (855) 658-5248 and we’ll get you booked. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- One torsion spring: $180 – $340 typical, installed.
- A matched pair of springs: about twice that, roughly $360 – $680.
- Price depends on spring type, door size and weight, and whether cables or other parts are worn.
- Both springs usually get replaced together so you aren’t back in the same spot in a few months.
- Estimates are free, and the written quote is the price you pay.
As Edison Garage Door Repair Co, we handle spring work as a core part of what we do, not as a side job. Our technicians have up to 9 years of experience, and they work on the most widely installed door and opener systems, including LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor.
Spring Replacement Cost Breakdown (2026)
Here’s how the numbers usually shake out for a spring job in Edison. These are typical estimated ranges for the local market, not a quote. Your written estimate is what counts.
| Line Item | Typical Estimated Cost |
|---|---|
| Single torsion spring replacement (part + labor) | $180 – $340 |
| Matched pair of torsion springs | About $360 – $680 (roughly double the single-spring range) |
| Spring replacement bundled with a full repair | $150 – $600 total, depending on what else is involved |
| Cable repair, if a cable is worn or frayed alongside the spring | $130 – $250 |
| Track realignment, if the door has shifted off track | $120 – $240 |
| Roller replacement, if rollers are worn | $110 – $220 |
| Opener repair, if the opener is straining or short-cycling | $120 – $320 |
A plain spring swap on a standard two-car door is the simple case. The cost moves up when the job isn’t just springs. Worn cables sitting next to a broken spring are a common pairing, because the same strain that snaps a spring can fray a cable. If the door has drifted off track, that gets corrected too before it’s safe to run. And when an opener has been fighting a broken spring for a while, its gears or motor can take damage, which turns a spring job into a spring-plus-opener job. These are the reasons two homes on the same block can get different estimates.
Spring replacement is genuinely the most dangerous repair on a garage door. Torsion springs hold a lot of stored tension, and a spring that lets go under the wrong hands can cause serious injury. That’s a big part of why we treat it as trained-technician work rather than a weekend project. For a fuller look at this part of the service, see our spring replacement page.
What Affects Spring Replacement Pricing in Edison
No two doors are identical, and the estimate reflects that. These are the factors that move the number up or down on a spring job in Edison.
- Spring type. Torsion springs (the horizontal ones mounted on a shaft above the door) are different work from extension springs (the ones that run along the tracks on each side). Torsion jobs are the more common configuration on newer Edison homes, but plenty of older properties still run extension springs, and the labor differs.
- Door size and weight. A single-car door takes lighter springs than a double-car door, and the spring has to match the weight it’s lifting. Heavier doors, insulated doors, and doors with more glass mean springs sized for that load, which can shift the price within the range.
- Whether it’s one spring or a pair. A broken spring almost always means the second spring is the same age and has taken the same wear. Replacing both together is usually the smarter call, even though it costs roughly double a single spring. Replacing one and coming back for the other in a few months usually costs more overall.
- Condition of the cables and drums. Cables, drums, and the center bearing plate all work with the springs. If any of them are worn, they get attention in the same visit so the door runs right afterward. That’s the “right part, the right fix, the first visit” approach, rather than a patch that fails again.
- Door age and hardware. An older door in Edison may have springs that are seized to the shaft or hardware that’s rusted or stripped. That adds time to the job, and time is part of the labor.
- Whether the opener has been stressed. Running an opener against a broken spring strains the motor and gears. If the opener has already taken damage, that gets diagnosed on the same visit so you’re not paying for two separate trips.
One thing we hear a lot: “the door is only a few years old, why did the spring break?” Springs are rated by cycles (one open plus one close), not by calendar age. A door that runs several times a day reaches its cycle limit faster than a door that runs twice a day. A household with people coming and going all day wears a spring out sooner than a quiet one, and that’s normal.
How to Save on Spring Replacement
There isn’t a magic discount on springs, but there are real ways to keep the total down without cutting corners.
- Get the estimate before anything is touched. A free estimate means you know the number before work starts. Call (855) 658-5248 and we’ll set one up. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
- Fix it before it fails. A spring that’s still holding but showing wear (a visible gap in the coil, or a door that’s gotten heavier to lift by hand) can be replaced on a scheduled visit. Waiting for the snap usually means the door is stuck in the down position and you’re dealing with it on the worst possible day.
- Replace the pair, not just the survivor. It costs more up front, but it prevents a second service visit within months. Two trips to fix two springs almost always cost more than one trip to fix both.
- Ask about the cables while the door is open. If a cable is frayed, fixing it during the spring job is cheaper than a second call later. The line items above show why.
- Keep the door balanced. A door that’s out of balance puts extra strain on the springs and the opener. A quick check (lift the door halfway by hand and see if it stays put) tells you if it needs attention. Don’t force a door that feels wrong; call instead.
- Don’t DIY the spring. We say this plainly because it’s true: torsion spring work is where serious injuries happen. The savings from a DIY attempt aren’t savings if something goes wrong.
If the door is beyond a spring fix, we also handle the bigger picture. From a broken spring to a brand-new door, we cover every stage. A full new door installation runs $700 – $2,200 typical, and we’ll tell you honestly when a repair is the better call and when replacement makes sense.
FAQs – Spring Replacement Cost
How much does garage door spring replacement cost in Edison?
Spring replacement in Edison typically costs $180 – $340 for one spring, installed. A matched pair runs about twice that, roughly $360 – $680. The written estimate sets the final price, and the estimate itself is free. Call (855) 658-5248 for an exact quote.
Is it cheaper to repair or replace a garage door spring?
Repairing is almost always the cheaper option, and a spring replacement at $180 – $340 is far less than a new door at $700 – $2,200 typical. Replacement only makes sense when the door itself is worn out, not just the spring. Call (855) 658-5248 and we’ll tell you which side of that line your door is on. Estimates are free.
Do I need to replace both springs if only one broke?
Usually yes, and it’s the better value. Both springs are the same age and have taken the same cycles, so the second one is often close behind. A pair costs about twice a single spring, roughly $360 – $680, but it avoids a second service visit within months. Call (855) 658-5248 for a quote on the pair.
Can you replace my springs the same day?
Often yes. Same-day spring replacement is possible when the parts for your door are on hand. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. If you call outside dispatch hours, we’ll book you into the next opening. Call (855) 658-5248 and we’ll get you back up and running today.
Why did my spring break in the first place?
Springs break from cycle wear, not age alone. A spring rated for a set number of open-and-close cycles gives out once it hits that count, and a busy Edison household reaches it faster than a quiet one. Rust, poor door balance, and a straining opener can shorten the life too. Whatever the cause, the fix starts with a look. Call (855) 658-5248; estimates are free.
Does spring replacement come with any other work?
It can, depending on what the technician finds. If cables, rollers, or tracks are worn, they get quoted as separate line items (cable repair $130 – $250, roller replacement $110 – $220, track realignment $120 – $240). You approve the written estimate before anything else is done. Call (855) 658-5248 to schedule.
Why Precision Matters on a Spring Job
A spring has to match the door. The wrong size or tension wears out fast, strains the opener, and can make the door unsafe to operate. That’s why we source the correct spring for the door in front of us rather than grabbing whatever’s closest. Our technicians work on the brand already in your garage, across LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor systems, so diagnosis is faster and the right part shows up on the first visit.
The single-company accountability matters too. From diagnosis to the finished repair, it’s the same team on the job, no handoffs. Spring repair is one piece of a full range that also covers opener repair, panel and door repair, and complete new-door installations. If your spring job uncovers a separate issue, you’re not hunting for a second vendor.
For a wider look at repair costs across the board, opener repair typically runs $120 – $320, panel replacement $250 – $500, and general garage door repair $150 – $600. New opener installation runs $250 – $550. All of these are typical estimated ranges for the Edison area, with the written estimate setting the final number.
When to Call Us
If your door won’t lift, if you heard a bang from the garage, or if the door feels heavy and won’t stay up, the spring is the first thing to check. Don’t force it. A trained technician can confirm the problem and give you a price before any work starts. Call (855) 658-5248 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Spring replacement done right, the first time, is a small job that keeps your door working for years. Precision over patchwork. That’s how we approach every spring in Edison.
Pricing reflects the Edison market as of 2026. Edison Garage Door Repair Co offers free estimates – call (855) 658-5248.
What Our Customers Say
"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Marcy Rhodes"Door installed in about four hours, old one hauled away, and he stayed to program both cars and the wall panel before he left."
- Riya Singh"Opener kept reversing halfway down. Turned out to be the safety sensors knocked out of alignment by a bicycle. He straightened them, wouldn't charge me for it, and just asked me to keep them in mind if I need real work later."
- Brian Norris